Preface This is the fifth edition of CSA B149.5, Installation code for propane fuel systems and containers on motor vehicles. It supersedes the previous editions, published in 2010, 2005 and 2000 by the Canadian Standards Association (CSA) as CAN/CSA-B149.5, and in 1995 by the Canadian Gas Association (CGA) as CAN/CGA-B149.5, under the title Installation code for propane fuel systems and tanks on highway vehicles. These requirements for the installation of propane fuel systems and tanks on motor vehicles were originally published in 1982 as an amendment to CAN/CGA-B149.2-80, Propane Installation Code, and were subsequently incorporated as Part 15 in the editions of CAN/CGA-B149.2 published in 1986 and 1991. In 1995, the Part 15 requirements were removed from CAN/CGA-B149.2 to create CAN/CGA-B149.5 for the convenience of those individuals involved with converting propane vehicles who do not require the CSA B149.1 and B149.2 Codes. In this 2015 edition, where a major change or addition to the previous edition of the Code has been made, the clause, table, or figure affected is identified by the symbol delta in the margin. Users of the Code are advised that the change markers in the text are not intended to be all-inclusive and are provided as a convenience only; such markers cannot constitute a comprehensive guide to the revisions made to the Code. Care must therefore be taken not to rely on the change markers to determine the current requirements of the Code. As always, users of the Code must consider the entire Code and any local amendments. The CSA B149.5 Installation Code for Propane Fuel Systems and Containers on Motor Vehicles Committee, which is responsible for preparing this Code, consists of members of the provincial gas inspection authorities, propane distributors, appliance, equipment, and accessory manufacturers, certification organizations, and representatives from the federal government departments. This Code has been formally approved by the CSA B149.5 Technical Committee for Propane Fuel Systems and Containers on Motor Vehicles and by the Interprovincial Gas Advisory Council. Scope 1.1 This Code applies to (a) the installation, servicing, and repair of propane fuel system components and containers on motor vehicles for the provision of motive power; and (b) the installation of containers, on motor vehicles such as recreational vehicles, outdoor food service units, and wash-mobiles when propane is to be used for fuel purposes (other than motive power). Note: Motor vehicles include when propane is used as an engine fuel in other than highway vehicles such as ice resurfacing machines, lift trucks, lawnmowers, etc. 1.2 This Code does not apply to (a) vehicles qualified under the Canada Motor Vehicle Safety Regulations*; (b) propane used on boats; and (c) the installation of appliances. *For confirmation of CMVSS compliance, you may contact the vehicle manufacturer or Transport Canada. 1.3 Where the term "propane" is used, the requirements of this Code include, and apply equally to, any material that is composed predominantly of any of the following hydrocarbons or a mixture of them: propane, propylene, butane (normal butane or isobutane), and butylenes. 1.4 This Code and any Standards referenced in it do not make or imply any assurance or guarantee with respect to the life expectancy, durability, or operating performance of equipment and materials referenced in the Code. 1.5 The values given in yard/pound units are the standard. This Code contains SI (metric) equivalents to yard/pound units so that the Code can be used in SI (metric) units. SI (metric) equivalents may be approximate. 1.6 In this Code, unless approved otherwise by the authority having jurisdiction, "shall" indicates a mandatory requirement; "should" indicates a recommendation or that which is advised but not mandatory; and "may" indicates an advisory or optional statement. Notes to the text do not include mandatory or alternative requirements. The purpose of a note is to separate from the text explanatory or informative material that is not properly a part of this Code. Notes to figures and tables, however, are considered part of the figure or table and may be written as mandatory requirements. Annexes are designated normative (mandatory) or informative (non-mandatory) to define their application.